Module spare parts REF615C-D HCFFAEAGABC2BAA1XD

Product Details

Product Description

Product Description
Focus on DCS, PLC, robot control system and large servo system.
Main products: various modules / cards, controllers, touch screens, servo drivers.
Advantages: supply of imported original products, professional production parts,
Fast delivery, accurate delivery time,
The main brands include ABB Bailey, Ge / fuanc, Foxboro, Invensys Triconex, Bently, A-B Rockwell, Emerson, ovation, Motorola, xyvom, Honeywell, Rexroth, KUKA, Ni, Deif, Yokogawa, Woodward, Ryan, Schneider, Yaskawa, Moog, prosoft and other brands

REF615C-D HCFFAEAGABC2BAA1XD

Caution Refer to the Read Me First: Safety and Radio-Frequency Interference document before removing equipment covers or connecting/disconnecting any signal wires. Power off the computer and, depending upon the device type, install the NI 435X following the instructions in this section. Note You can plug in the NI PCMCIA-4350 and NI USB-4350 at any time after the drivers are installed without powering off the computer. © National Instruments Corporation 5 Where to Start with the NI 435X ♦ NI PCMCIA-4350 Figure 1. NI PCMCIA-4350 System You can install the NI PCMCIA-4350 in any available Type II PCMCIA slot in the computer. Windows 98 or later includes the Plug and Play services that the operating system uses. Windows NT 4.0 or higher includes the drivers needed to use PCMCIA cards. The operating system configures the NI PCMCIA-4350 and automatically assigns the base address and the interrupt level. The following are general installation instructions, but consult the PC user manual or technical reference manual for specific instructions and warnings: 1. Write down the NI PCMCIA-4350 serial number for future reference. 2. Power off the computer. Note If the computer and operating system support hot insertion, you can insert or remove the NI PCMCIA-4350 at any time, even if the computer is powered on. 3. Remove the PCMCIA slot cover on the computer. 1 Portable Computer 2 PCMCIA Socket 3 NI PCMCIA-4350 1 2 3 Where to Start with the NI 435X 6 4. Insert the 68-pin I/O connector of the NI PCMCIA-4350 into the PCMCIA slot until the connector is firmly seated. The NI PCMCIA-4350 connectors are keyed so the device can only be inserted in one way. The NI PCMCIA-4350 is now installed. Refer to the Configuring and Testing the NI 435X section next. ♦ NI USB-4350 Figure 2. NI USB-4350 with USB Cable Note The NI USB-4350 is only supported in Windows 2000/XP/Me/98. You can connect the NI USB-4350 to any available USB connector that supports high-power, bus-powered peripheral devices. The following are general installation instructions, but consult the PC user manual or technical reference manual for specific instructions and warnings. 1. Connect the USB cable from the computer port or from any other hub, to the port on the NI USB-4350. 2. The computer should immediately detect the NI USB-4350. When the computer recognizes the NI USB-4350, the LED on the front panel blinks or lights up, depending on the state of the device. If the LED lights up after the NI USB-4350 is connected to the host, the NI USB-4350 is functioning properly. If the LED remains off or blinks, refer to Table 1. 1 NI USB-4350 2 Downstream USB Connector 3 Upstream USB Connector to PC 1 3 2 © National Instruments Corporation 7 Where to Start with the NI 435X The NI USB-4350 is now installed. Refer to the Configuring and Testing the NI 435X section next. Table 1. LED